Hoses High Pressure Hose 1sn 2sn From 215 Bar
A hydraulic hose is used anywhere in a hydraulic system requiring a flexible connection between two fluid ports. A hydraulic hose is a synthetic rubber tube surrounded by some sort of flexible strength enhancing winding, such as metal or fiber, and then covered in another rubber carcass
HAIKUO products are analyzed for quality assurance and specifications at many points of the manufacturing process to insure that we ship the very best finished products to our customers. In addition, we perform hydraulic pressure testing and impulse testing to ensure that our products perform to rated specifications.
To compliment our hose products, choose from a variety of accessories, such as steel, brass, and stainless steel hydraulic adapters and split flange kits. To enhance hose life and performance we have spring guards, nylon hose sleeving, and spiral-guard hose sleeving. These products are manufactured from the same sources as the largest hose manufacturing names at a significant price savings.
Product Quality
(1) hose layout should avoid heat source as far as possible, away from the performance of engine exhaust pipe.If necessary, the casing or protective screen can be used to prevent the hose from heat deterioration.
(2) where the hose must cross or may rub against the mechanical surface during operation, the hose clamp or spring and other protective devices shall be applied to avoid damage to the outer layer of the hose.
(3) when the hose must be bent, the bending radius should not be too small, should be greater than 9 times the outside diameter.The connection between the rubber hose and the joint shall have a straight section greater than 2 times the outer diameter of the pipe.
(4) when installing the hose, avoid being in a tensioned state. Even if there is no relative movement between the two ends of the hose, keep the hose loose. The tensioned hose will expand under pressure and reduce its strength.
(5) do not twist the hose during installation.Slight torsion of the hose may reduce its strength and loosen the joint. Tighten the joint on the hose rather than the hose on the joint during assembly.
(6) if the hose is installed on key parts, it is recommended to carry out regular inspection or replacement.
| Standard | Hose ID (mm) | Wire OD | Hose OD (mm) | Working Pressure | Burst Pressure | Weight (kg/meter) | |||
| inch | mm | mm | (Mpa) | (Psi) | (Mpa) | (Psi) | |||
| SAE 100R1 AT | 1/4 | 6.4 | 11.1 | 13.4 | 22.5 | 3270 | 90 | 12840 | 0.23 |
| 5/16 | 7.9 | 12.7 | 15 | 21.5 | 3120 | 85 | 12280 | 0.289 | |
| 3/8 | 9.5 | 15.1 | 17.4 | 18 | 2610 | 72 | 10280 | 0.34 | |
| 1/2 | 12.7 | 18.3 | 20.6 | 16 | 2320 | 64 | 9180 | 0.42 | |
| 5/8 | 15.9 | 21.4 | 23.7 | 13 | 1890 | 52 | 7420 | 0.49 | |
| 3/4 | 19 | 25.4 | 27.7 | 10.5 | 1530 | 42 | 6000 | 0.61 | |
| 1 | 25.4 | 33.3 | 35.6 | 8.8 | 1280 | 35 | 5020 | 0.94 | |
| 1-1/4 | 31.8 | 40.5 | 40.5 | 6.3 | 920 | 25 | 3600 | 1.18 | |
| 1-1/2 | 38.1 | 46.8 | 46.8 | 5 | 730 | 20 | 2860 | 1.35 | |
| 2 | 50.8 | 60.2 | 60.2 | 4 | 580 | 16 | 2280 | 1.84 | |
Hot Tags: hoses high pressure hose 1sn 2sn from 215 bar, China, suppliers, manufacturers, factory, low price, PTFE High Pressure Hose, High Pressure Washing Hose, 1 Wire Braid High Pressure Hose DIN EN 856 1SNK, 1 Layer Steel Wire Braid Hyraulic Pipe SAE R1A DIN EN 853 1ST, Steel Wire Braid Hydraulic Hose, 1 Wire Braid Hyraulic Hose SAE R1AT DIN EN 853 1SN
You Might Also Like
Send Inquiry